The Beam Reaction Calculator finds ideal support reactions for a horizontal, simply supported pin-and-roller beam or a cantilever fixed at its left end. Enter zero to six vertical point loads and, optionally, one uniform distributed load over a full or partial length. The calculator balances signed vertical forces and their moments using the stated support model. It does not select a beam section, establish load combinations, calculate deflection or certify a structure, connection or foundation.
Key Takeaways
- Choose the correct support model before entering loads: pin/roller ends and a fixed-left cantilever have different reactions.
- Applied loads are positive downward and negative upward. Support reaction forces are positive upward; a fixed reaction moment is positive counterclockwise.
- All positions are measured from the left end A. Point loads must lie between x=0 and x=L; no overhang is modeled.
- A uniform load q over a–b has equivalent force W=q(b−a), acting at c=(a+b)/2 from A.
- A negative vertical reaction means that the assumed support must act downward. A bearing-only support may not provide that restraint.
- Self-weight, other loads and design factors are included only when you explicitly supply them. Equilibrium is not a strength or stability approval.
Supported beam arrangements
Simply supported: pin A and roller B
The beam spans from A at x=0 to B at x=L. The ideal pin restrains translation and allows rotation; the ideal roller provides a vertical reaction without an end reaction couple. With the vertical loads supported by this tool, the calculated horizontal reaction is zero. The unknown vertical forces are R_A and R_B.
This is not a fixed-fixed beam, continuous beam, propped cantilever or a beam with an overhang. A real connection that looks like a pin or a fixed support may behave differently. Establish the analytical idealization and its relevance to the structure through the responsible engineer.
Cantilever: fixed A and free right end
The cantilever is fixed at x=0 and free at x=L. It has a vertical reaction V_A and a reaction moment M_A at A, with no support at the right end. The fixed moment shown is an external support reaction, not a complete internal bending-moment diagram or a connection-capacity check.
Felix Udoeyo's Structural Analysis chapter on equilibrium and supports explains ideal support characteristics and statically determinate reactions. This calculator implements only the two explicitly named arrangements under vertical loading, not every support or load case described in that text.
Inputs and load conventions
Beam length and coordinates
Enter the positive horizontal beam length L. Every point-load coordinate and distributed-load endpoint is a distance from the same left end A. Coordinates can use different supported length units, but they must refer to that same datum. A load at x=0 or x=L is allowed. A load outside that interval is rejected rather than silently treated as an overhang load.
Supported length units are international feet, inches, yards, meters, centimeters and millimeters. Changing a unit retains its number; re-enter the corresponding quantity in the new unit. Do not substitute a sloping distance, an architectural grid reference or a distance measured from the opposite end without translating it into the defined coordinate system.
Signed vertical point loads
A point load has a magnitude, force unit and coordinate. Positive values act downward; negative values act upward. The force units are kip, lbf, kN and N. A kip is 1,000 pounds-force; it is not a unit of mass. Inclined forces are not directly supported, and entering only an inclined force's vertical component would omit its horizontal effect from this model.
Added rows start blank so a new load is not silently assumed. Zero to six rows are supported, and zero force is a valid explicit value. Loads at the same coordinate are added algebraically; this can represent separate coincident actions, but avoid duplicating the same real load. Optional names and source notes help preserve the loading basis.
One uniform distributed load
Enable the distributed load when a constant intensity acts from a to b. Enter a signed intensity in force per length, not a total force or an area pressure. The supported units are kip/ft, lbf/ft, lbf/in, kN/m and N/m. The endpoints must satisfy 0 ≤ a < b ≤ L.
For a full-span load, enter a=0 and b=L. For a partial load, keep the actual endpoints: moving the same total load to midspan changes its moment unless its original centroid was there. Triangular, trapezoidal and other varying intensities are outside this interface. It does not automatically convert an area pressure using tributary width.
Sign convention: separate loads from reactions
The calculator deliberately states separate directions for input loads and output reactions:
- P and q: positive downward, negative upward.
- R_A, R_B and V_A: positive upward, negative downward.
- M_A at a fixed support: positive counterclockwise, negative clockwise.
Define the load first-moment sum M_D = Σ(P_i x_i) + Wc. Because a positive entered force is downward and its coordinate is to the right of A, positive M_D represents clockwise loading about A. The counterclockwise fixed reaction moment balancing it is therefore M_A = M_D. Do not reinterpret M_D as a counterclockwise-positive applied moment.
The input note and copied summary retain these conventions. If comparing another analysis, translate its signs and support directions before comparing the numbers. A negative answer is not automatically an error: it may show that an assumed reaction direction must reverse.
Uniform-load equivalent and equilibrium equations
For constant signed intensity q over the interval a–b:
- Loaded length ℓ = b − a.
- Equivalent force W = qℓ.
- Equivalent coordinate c = (a+b)/2.
- Total signed downward load F = ΣP_i + W.
- Clockwise-positive load first-moment sum M_D = Σ(P_i x_i) + Wc.
Engineering Statics: Open and Interactive, distributed loads explains replacing a distributed load with a resultant through the loading distribution's centroid for external equilibrium. That replacement does not preserve the internal shear or bending distribution at every section. This page uses it to find support reactions only.
Simply supported reactions
Take moments about A and then balance vertical forces:
R_B = M_D/L
R_A = F − R_B
The corresponding checks are R_A + R_B − F = 0 and R_B L − M_D = 0. No end reaction couple is assigned to either ideal simple support.
Left-fixed cantilever reactions
The fixed support balances all vertical force and moment:
V_A = F
M_A = M_D
The free right end is not given a reaction. No stiffness or elastic modulus is needed for these external reactions in the stated statically determinate models. Their absence is not evidence that stiffness and material properties are irrelevant to member design or deflection.
Worked US example: point load plus full-span uniform load
Fictional teaching example: a 20 ft simply supported beam carries a 4 kip downward point load at x=8 ft and a 0.2 kip/ft downward uniform load over x=0–20 ft. No other load, including self-weight, is assumed.
- Uniform resultant: W = 0.2 × 20 = 4 kip.
- Uniform resultant position: c = (0+20)/2 = 10 ft.
- Total downward load: F = 4+4 = 8 kip.
- Load first-moment sum: M_D = 4×8 + 4×10 = 72 kip·ft.
- Right reaction: R_B = 72/20 = 3.6 kip upward.
- Left reaction: R_A = 8−3.6 = 4.4 kip upward.
Check forces: 4.4+3.6 = 8 kip. Check moments about A: 3.6×20 = 72 kip·ft. Those equations close for the entered model; they do not confirm that the assumed loads or support details describe a real project.
If the same loading acts on a cantilever fixed at A instead, the vertical reaction is 8 kip upward and the fixed reaction moment is 72 kip·ft counterclockwise. There is no reaction B. The loading is unchanged, but the support arrangement changes which reactions are available to balance it.
Worked metric example: a partial uniform load
Consider a fictional 6 m simply supported beam, a 12 kN downward point load at x=1 m, and a 10 kN/m downward uniform load from x=2 m to x=5 m.
- Loaded segment length = 5−2 = 3 m.
- Uniform resultant W = 10×3 = 30 kN.
- Centroid c = (2+5)/2 = 3.5 m from A.
- Total load F = 12+30 = 42 kN.
- M_D = 12×1 + 30×3.5 = 117 kN·m.
- R_B = 117/6 = 19.5 kN upward.
- R_A = 42−19.5 = 22.5 kN upward.
It would be incorrect to apply 10 kN/m over the entire 6 m or to place the partial load's resultant automatically at x=3 m. For the same entered loads on a left-fixed cantilever, V_A = 42 kN upward and M_A = 117 kN·m counterclockwise.
Interpreting negative reactions and zero net load
An upward applied load can require a downward support reaction. The calculator preserves that sign rather than replacing it with an absolute value or forcing a reaction to zero. Whether a real support can provide the required restraint is a separate physical question.
A simple bearing or unanchored roller cannot necessarily pull downward on a beam that tends to lift away. If the result demands that action, the assumed restraint may not exist. The interface flags a required downward reaction so the support, anchorage and validity of the ideal model can be assessed professionally.
Zero total force does not mean zero moment
For a fictional 5 m simple beam with a 10 kN upward load at A and a 10 kN downward load at B, the net applied vertical force is zero. However, M_D = (−10×0)+(10×5) = 50 kN·m. The reactions are R_B = 10 kN upward and R_A = −10 kN, meaning 10 kN downward.
These opposite loads create a couple through their separation, even though this tool has no independent applied-couple input. Do not delete loads because their signed forces add to zero. Likewise, do not compute a single overall resultant coordinate by dividing moment by net force when net force is zero; the separate force and moment sums remain meaningful.
Units, self-weight and load combinations
The implementation uses exact international length ratios and force conversions before displaying results. One international foot is 0.3048 m. One pound-force is 4.4482216152605 N, obtained from the defined pound mass and standard gravity convention; one kip is 1,000 lbf. NIST's SI Guide footnotes explain the underlying conventional conversion factors.
Self-weight is not automatic. If it belongs in the load case, establish the appropriate line load and include it explicitly without counting it twice. This calculator does not know a section's dimensions, density, actual tributary area or project loading criteria.
It does not select service, factored, ultimate, wind, seismic or other combinations. Use a consistently defined load case supplied through the appropriate design process. Do not combine a factored point load with an unfactored distributed load and interpret the output as a verified code load combination.
What is outside this calculation?
- Horizontal or inclined forces and three-dimensional effects.
- Independent applied couples, overhangs and intermediate supports.
- Fixed-fixed, propped, continuous or otherwise indeterminate systems.
- Triangular, trapezoidal or nonuniform distributed loads.
- Shear-force and bending-moment diagrams, deflection and vibration.
- Beam size, material, reinforcement, buckling, bearing or connection capacity.
- Foundation design, support settlement, construction sequence and approval.
A result satisfying two equilibrium equations is only as useful as its loading and support assumptions. A real member must also meet the relevant strength, serviceability, stability, detailing and support requirements. Use this tool as a transparent statics aid alongside a qualified engineer's project assessment.
The distinct Beam and Column Rebar Quantity Calculator is a quantity tool under its own assumptions, not a way to design reinforcement from these reactions. Do not infer reinforcement, a footing size or a safe load from this page's support numbers alone.
Validation and practical review checklist
Length inputs accept unsigned decimals with up to 18 decimal places. Force and intensity inputs accept signed decimals, with positive downward and negative upward. Commas and exponent notation are rejected. Beam length must be positive and no greater than 10,000 m; each point force magnitude is limited to one billion N, and uniform intensity magnitude to one billion N/m. These are software limits, not physical design capacities.
The point-load count is zero to six. Names are limited to 80 characters and notes to 500. A disabled uniform load is ignored. If enabled, its endpoints must define a positive-length interval within the beam even when intensity is zero. Any edit clears the previous result; an error identifies and focuses its input.
- Confirm that the support arrangement matches one of the two supported models.
- Record length and the common coordinate origin A.
- Check each force sign, unit and location against the load source.
- Check distributed intensity units, endpoints and equivalent centroid.
- State whether self-weight is included and preserve the load-case basis.
- Verify both force and moment balance using the displayed assumptions.
- Review any required downward restraint or reversed fixed moment.
- Keep the calculation with the drawings and professional review record.
The daily report generator can document observed support conditions and unresolved design queries. A site observation or photograph is supporting information, not confirmation that the ideal analytical restraint exists.
Frequently asked questions
Why is the nearer support reaction usually larger for one downward point load?
For a simple beam with a point load P at x, R_B=Px/L and R_A=P(L−x)/L. Moving the load toward A reduces R_B and increases R_A. Additional or upward loads can change that simple pattern.
Can a load sit directly on a support?
Yes, x=0 and x=L are valid endpoints. In a simple model, a point load at A has zero moment about A and contributes to the reaction there. The calculator does not check the actual local bearing or connection detail.
Why is there no right reaction for a cantilever?
The selected model has a free right end. Its left fixed support provides the vertical reaction and balancing reaction moment. Adding a right support would create a different model that this interface does not solve.
Does a negative reaction mean the arithmetic failed?
Not necessarily. It reverses the assumed upward reaction direction. Check load signs and coordinates, then assess whether the real restraint can deliver the downward action. An algebraic solution is not proof of contact or anchorage.
Can I use an area load such as pounds per square foot?
Not directly. The uniform input is force per beam length. Establish the relevant tributary width and load path through the appropriate design process before converting an area pressure into a line load.
Can the calculator give zero reactions?
Yes, for an unloaded or suitably self-equilibrated entered system. It does not automatically include self-weight or omitted project actions, and a zero net force by itself does not imply a zero moment.
Methods, references and corrections
All worked scenarios here are original fictional examples. Independent reference tests use exact fraction arithmetic for load conversions, force totals, first moments and reactions, without importing the application model. They include US/metric inputs, partial loads, endpoint forces, cantilevers, signed cancellation and tiny differences near coordinate boundaries.
The linked Udoeyo chapter supports the equilibrium and ideal-restraint concepts; Engineering Statics explains distributed-load resultants and centroids; NIST provides unit-conversion context. This page does not reproduce a complete design standard. Technical review completed by Riya Kulkarni | BE Civil Engineer; completion confirmed on 14 November 2026. Read Civilable's methods and corrections policy or contact Civilable with exact inputs, units, support assumptions and an expected reference calculation if you identify an error.