Formula and worked example
Let L be the outside-wall building length, S the horizontal wall span, E the horizontal end overhang at each end of L, and H the horizontal slope-edge overhang at each side of S. Roof plan area = (L+2E)(S+2H). With rise r per 12 horizontal run, surface factor = sqrt[1+(r/12)²]. Gross sloped area = plan area × factor. Angle mode instead uses 1/cos(angle), with angle measured above horizontal.
A symmetric gable has two equal rectangular planes: each runs half the overhang-inclusive span and has half the total gross surface area. A shed has one rectangular plane across the full span. Total area is equal for these two forms when outline and uniform slope are identical; per-plane dimensions differ. This is geometric area, not a rafter-cut or framing design.
Independent US reference
A 40×30 ft outside-wall rectangle with 1 ft horizontal overhang at every edge gives a 42×32 ft roof plan, or 1,344 ft². At 6:12, the factor is sqrt(1.25)=1.118033988750. Gross surface is 672×sqrt(5)=1,502.637680880 ft², or 751.318840440 ft² per gable plane. Horizontal run per plane is 16 ft and sloped width is 17.888543820 ft. Subtracting 100 ft² of measured actual roof-surface openings gives 1,402.637680880 ft² net, or 14.026376809 roofing squares. Do not double the entire plan area again for the two gable sides.
Without overhangs, the same building has 1,341.640786500 ft² of sloped surface. The overhangs add 160.996894380 ft² at this slope. These are original arithmetic examples, not a building specification.
Independent metric reference
A 10×8 m wall rectangle with 0.5 m overhang on every edge gives 11×9=99 m² of roof plan. At 9:12, the factor is exactly 1.25, so gross surface is 123.75 m². Deducting 3.75 m² measured on the roof gives 120 m² net. Each gable plane has 61.875 m² gross before deductions. A shed with the same outline and slope has one 123.75 m² gross plane. Metric areas use SI geometry; no material allowance is implied.
Enter horizontal overhangs once
Dimensions here describe the outside-wall footprint. Overhangs are horizontal plan distances, not sloping rafter-tail lengths. If source dimensions already measure the outer roof outline, enter zero overhang. Equal amounts apply at opposite edges. End overhang extends length; slope-edge overhang extends span, including high and low edges for a shed. Irregular, asymmetric or intersecting outlines need separate plane measurements instead of forcing them into one rectangle.
Slope and deductions
Rise per 12 uses horizontal run, not the full building span. Angles are degrees above horizontal. Inactive slope fields are ignored; switching mode does not infer another measurement. Zero slope describes level geometry and forms no gable ridge; it is not approval of a roofing material. Deductions must be measured areas on the actual roof plane and are subtracted once after slope adjustment. They are not horizontal opening projections and are not automatically assigned to a particular plane.
Measured area versus material ordering
One roofing square is 100 ft² of area. No cutting waste, laps, bundle rounding, starter, ridge material, flashing, ventilation, fasteners or cost is added here. Use Roofing Calculator for a coverage allowance or Roof Shingles Calculator for product-specific bundles. Roof Pitch Calculator remains a separate rise/run conversion tool. Roofs with hips, valleys, dormers, unequal pitches or nonrectangular planes require a detailed takeoff.
Primary reference
TAMCO: Roof Slope Factors describes horizontal roof footprint, slope factors and overhang measurement. Civilable computes the factor from geometry rather than copying rounded table entries. Inputs use exact decimal fractions; square-root and trigonometric calculations use floating-point arithmetic, with area results displayed to three decimals. Reference inspected 30 October 2026. No product slope suitability, code or structural approval is inferred.