Civil engineering

Excavation Calculator

Measure rectangular bank excavation and estimate the separate loose volume after your chosen material swell.

Created and Written by: Designation: Founder

Technically reviewed by: Riya Kulkarni | BE Civil Engineer

Define the excavation envelope

Dimensions and 20% swell are editable examples. Use surveyed or planned excavation extents and a material-specific swell value. Bank volume describes the in-place material; loose volume describes it after excavation.

1. Rectangular dimensions

Use horizontal plan length and width with a uniform vertical depth. Count repeats identical, separate, non-overlapping rectangular excavations. If dimensions already describe the complete excavation, leave extra clearance off. This model assumes the envelope is filled with material before excavation.

2. Optional working clearance

When enabled, add the same clearance c at both ends of length and width: effective footprint = (L + 2c) × (W + 2c). Depth stays unchanged. Clearance extends the whole rectangular prism; it is not a side slope or a bench. Enter the amount from your layout and avoid adding it again when already included in reference dimensions.

3. Bank-to-loose material swell

Loose volume = bank volume × (1 + swell / 100). A 20% entry means factor 1.20, not 20 times the bank volume. Swell affects the excavated material’s volume, not the hole dimensions. Zero is allowed. This page does not convert to compacted fill or infer swell from soil names.

EXAMPLE · BANK VOLUME
35.556 yd³

In-place bank excavation · 960 ft³ / 27.184 m³

Identical excavations
1
Effective footprint each
20 × 12 ft
Horizontal area each
240 ft²
Vertical depth
4 ft
Working clearance per side
0 ft · disabled
Bank volume each
35.556 yd³ / 27.184 m³
Total bank volume without added clearance
960 ft³
Bank volume added by clearance
0 ft³
User-entered swell
20% / factor 1.2
Swell volume increase
192 ft³ / 5.437 m³
Total loose excavated volume
42.667 yd³ / 32.621 m³
Total loose volume in ft³
1,152 ft³
Loose volume rounded up (0.1 m³)
32.7 m³

Calculation basis

Bank = (L + 2c) × (W + 2c) × depth × count. Clearance c = 0 when disabled. Loose = bank × (1 + swell / 100). Bank cubic yards (BCY) and loose cubic yards (LCY) measure different material states; both are shown separately.

Constant-depth rectangular prisms only. No side slopes, benches, support design, occupied-volume deductions, compaction, weight, truck loads or cost calculated. Irregular ground and changing depths require a separate takeoff. Volumes use exact decimal fractions and are displayed to 3 decimals, without order or haul rounding. The separate 0.1 m³ round-up is a reporting figure; it does not change bank or loose volumes.

Formula and worked example

For identical rectangular excavations, let L and W be reference horizontal length and width, D be uniform vertical depth, c be optional horizontal working clearance on each side, and n be the excavation count. Effective dimensions are L + 2c and W + 2c. Bank volume B = (L + 2c)(W + 2c)D × n. When clearance is disabled, c = 0. The added clearance volume equals B minus LWD × n; the expanded footprint counts the corners once.

Bank volume describes material before disturbance, in its in-place state. Loose volume after excavation = B × (1 + s/100), where s is your bank-to-loose swell percentage. The difference is B × s/100. Swell changes the material volume after excavation, not the size of the excavation envelope. A 20% entry is factor 1.20; it is not a compacted-fill percentage.

Independent US example

A 20 × 12 ft excavation with uniform 4 ft depth and no added clearance gives 960 ft³ bank volume. Divide by 27 to obtain 35.555555556 bank yd³ (BCY), or 27.184172728320 m³. At an illustrative 20% swell, loose material is 1,152 ft³, or 42.666666667 loose yd³ (LCY), or 32.621007273984 m³. The 192 ft³ swell increase does not increase the bank excavation quantity.

Enabling 2 ft clearance on every side changes the footprint to 24 × 16 ft. Bank volume becomes 1,536 ft³ and the clearance adds 576 ft³. At 20% swell, loose volume becomes 1,843.2 ft³, or 68.266666667 yd³. Two identical non-overlapping excavations give 3,072 ft³ bank and 3,686.4 ft³ loose; the dimensions of each excavation stay unchanged. If your original dimensions already are 24 × 16 ft, keep clearance disabled to avoid adding it twice.

Independent metric example

A 5 × 3 m rectangle at 2 m vertical depth gives 30 m³ bank and 36 m³ loose at 20% swell. A 0.5 m clearance at each side gives a 6 × 4 m footprint and 48 m³ bank per excavation. Three identical excavations total 144 m³ bank. The swell increase is 28.8 m³, giving 172.8 m³ loose material. The 20% input is an arithmetic example, not a soil classification or recommended allowance.

Enter the intended excavation extents

Use plan dimensions and a uniform depth from the survey or excavation layout. If the reference dimensions are a structure or work zone that needs a uniform extra working envelope, enable clearance and supply that distance. Clearance expands length and width, never depth. The model is a rectangular prism of unchanged width with depth; it does not infer side slopes, benches, shoring or a support arrangement.

The count repeats identical, separate excavations. Overlapping envelopes must not be counted twice. Split stepped or changing-depth work into appropriate non-overlapping quantities outside this one-box model. It does not automatically deduct existing structures, empty voids or material retained within the envelope. Irregular terrain, battered sides and varying sections need a takeoff matching that geometry.

Keep bank, loose and compacted quantities separate

Bank cubic yards and loose cubic yards are both volume units, but describe different material states. Changing swell leaves bank volume unchanged. Zero swell makes loose and bank volumes equal; 100% swell doubles the loose volume. Use project measurements or geotechnical/material data for the percentage. This page does not infer material factors from a soil name, predict settlement, compute compacted fill/backfill, select truck loads, estimate weight or price excavation work.

One international foot is 0.3048 m exactly; 1 ft³ = 0.028316846592 m³, and 1 yd³ = 27 ft³ = 0.764554857984 m³. The existing Cubic Yard Calculator remains a general volume tool. This excavation page labels the in-place envelope and separate excavated loose material explicitly.

Input and display limits

Length, width and depth accept ft, in, yd, m, cm or mm, independently, and up to 18 decimal places. Positive dimensions must be 0.000001–1,000,000 ft; expanded plan dimensions also may not exceed 1,000,000 ft. Enabled working clearance accepts 0–100 ft per side; hidden clearance is ignored when disabled. Count must be a whole number from 1 to 10,000. Combined bank volume is limited to 1,000,000 m³. Swell accepts 0–100% with four decimal places. These are calculation safeguards, not excavation-design limits.

Decimal dimensions, exact conversions, clearance geometry, repeated quantities and swell arithmetic use exact fractions. Results display to three decimals, without rounding up to an order increment or truckload. The separate loose-volume reporting figure rounds up to the next 0.1 m³, retaining exact multiples; this does not change the bank or loose calculation. Very small valid quantities may display as zero at this precision. Geometry here does not establish an excavation method or support design; take those requirements from the project layout and design.

Primary references

Caterpillar: Swell & Void Percentage, Load Factors describes swell as an increase from the original bank state to the loose state. Caterpillar: Material Density Tables to Help Estimate Earthwork Volumes distinguishes bank, loose and compacted states. References inspected 30 October 2026. Civilable uses the stated bank-to-loose percentage formula and original examples; it does not select material-table factors or apply a compacted-volume adjustment.

Related calculators

All calculators

TECHNICAL REVIEWER

Riya Kulkarni | BE Civil Engineer

Riya Kulkarni qualifications and experience
QualificationBE Civil – Shivaji University, Kolhapur (2018)
Experience8+ Years
Technical SpecialisationsStructural Engineering, Construction Materials, Site Execution and Concrete Technology.

Project experience

1. Shree Ganesh Residency

Location: Rajarampuri, Kolhapur

Project Type: G+4 Residential Apartment Building

Technical responsibilities
  • RCC structural construction coordination.
  • Reinforcement and shuttering inspection.
  • Concrete pouring and curing supervision.
  • Monitoring construction materials and workmanship.
  • Site quality-control documentation.

2. Vrindavan Heights

Location: Tarabai Park, Kolhapur

Project Type: G+5 Residential Building

Technical responsibilities
  • Structural drawing interpretation.
  • Reinforcement detailing checks.
  • Concrete workability and placement monitoring.
  • Construction sequencing and site coordination.
  • Building material quality assessment.

3. Sai Krupa Row Houses

Location: Kalamba Road, Kolhapur

Project Type: Residential Row Housing Development

Technical responsibilities
  • Foundation and plinth construction coordination.
  • Brick masonry and plastering inspection.
  • Concrete mixing, placement and curing.
  • Waterproofing and finishing work coordination.
  • Construction progress documentation.

4. Greenview Enclave

Location: Ujalaiwadi, Kolhapur

Project Type: G+3 Residential Apartment Complex

Technical responsibilities
  • Site execution monitoring.
  • RCC work and reinforcement inspection.
  • Construction material management.
  • Concrete quality testing coordination.
  • Workmanship and quality documentation.

5. Lotus Business Plaza

Location: Shahupuri, Kolhapur

Project Type: G+3 Commercial Building

Technical responsibilities
  • Structural construction coordination.
  • Slab and column reinforcement inspection.
  • Concrete placement and quality monitoring.
  • Construction activity sequencing.
  • Contractor and site-team coordination.

6. Omkar Residency

Location: Kadamwadi, Kolhapur

Project Type: G+5 Residential Apartment Building

Technical responsibilities
  • Foundation and superstructure execution coordination.
  • Reinforcement and formwork inspection.
  • Concrete testing and curing monitoring.
  • Material specifications and quality checks.
  • Site inspection reporting.

7. Silver Oak Villas

Location: Kasaba Bawada, Kolhapur

Project Type: Independent Residential Villa Development

Technical responsibilities
  • Residential foundation construction.
  • RCC structural component inspection.
  • Masonry and plastering quality checks.
  • Flooring and finishing coordination.
  • Site execution and material monitoring.

8. Pratham Commercial Complex

Location: Ruikar Colony, Kolhapur

Project Type: Commercial and Retail Building

Technical responsibilities
  • RCC construction coordination.
  • Concrete quality-control procedures.
  • Structural component inspection.
  • Construction material assessment.
  • Execution progress and quality reporting.